Since nothing corresponds with those part numbers, I recommend measuring your existing struts to find a replacement. For example, the Gas Shock # 372-5300-60 measures 20" extended and 11.41" compressed. If you have similar measurements you could use this as a replacement. If you need a 10 mm ball socket for the struts you can use the # 372BR-1020 or # 372BR-12553 for installation.
I have attached a link to all of our gas struts which can be filtered by extended length for your reference. view full answer...
From what I was able to find, the 2013 Heartland Gateway 3200RS has a GVWR of 14000-lbs, so it would be most likely that the trailer has 5200-lbs or 7000-lbs axles; this size axle would have hubs that accept 12" brakes, so you're likely correct. If you can confirm that your axles have that capacity then they will take 12" brake assemblies.
To replace those old brakes I recommend using the Electric Trailer Brake Kit - Self-Adjusting - 12" - Left and Right Hand Assemblies - 5.2K to 7K #... view full answer...
I looked up pictures of your 2021 Heartland Prowler and the taillights it uses are the part # RVSTB60 for the passenger side and # RVSTB61 for the driver side. view full answer...
The Replacement Printed Circuit Board for MaxxAir Powered Lift RV Roof Vents w/ Reversible Fan # MA10A21275K will work if you have one of the following roof vent models on your 2019 Heartland Torque 371 Toy Hauler:
- MaxxFan Plus: 00-04500K, 00-04700K, 00-04800K, and 00-04900K
- MaxxFan Deluxe: 00-0700K, 00-07500K, 00-08500K, 00-08700K, and 00-08900K
If you have a different model on your 5th wheel just let me know what it is and I can see if we have a replacement for you. Unfortunately... view full answer...
The CRE3000 Equalizers # MR59ZR are a great choice for an equalizer upgrade, but there is not a specific hanger set that would go with them. I can definitely help and point you in the right direction. Now, I do not have a way to know specs on your hangers based on a make and model of camper. If only it were so easy!
When replacing hangers it is important that we get the height of the hanger correct. This was we can retain the factory ride height. For example part # 28-5 is a very common... view full answer...
We do have the exact bearings, races, and grease seal you need for your 4,400 lb Dexter axle, and while there isn't a single kit with the parts, you can get them all individually. What you will need are the following:
- Bearings # L68149 and # LM67048
- Races # L68111 and # LM67010
- Grease Seals # RG06-050 view full answer...
Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part # BVD0449-A01 that you referenced if you wanted white or the part # BVD0449-A03 for the same smoke color you have now. view full answer...
In order to find a replacement clearance light for your 2020 Mallard M252 Travel Trailer I recommend taking some measurements. The # MCL31AB is 4" long x 2-1/16" tall x 1" deep. This is an LED light that uses a 2-wire design for power. If this matches your light from the other side in terms of dimension and appearance then it would make a good replacement.
If you send me the dimensions of the light on the other side and a picture I would be happy to look for a different replacement if... view full answer...
In order to find the correct replacement for your 2011 Heartland Elkridge you are going to need to identify your current pin box. Typically there is a sticker located on the pin box or king pin with the pin box number. If you are unable to find the sticker then you may be able to contact the manufacturer with the VIN to see what pin box it has. If all else fails, you will need to measure the bolt pattern. See the attached article for how to measure the bolt pattern and identify your pin... view full answer...
There are no replacement hoses for the RV Kitchen Faucet w/ Pull Down Spout # 277-000129; if your hose was damaged and irreparable you will need to replace your entire faucet; while that is understandably not the news you wanted to hear, these faucets do need to be replaced if the hoses are damaged. view full answer...
If you're just needing the handle part of your waste valve then you should be able to use either the Replacement Handle for LaSalle Bristol Cable-Actuated RV Waste Valves # 34490CMA1G which uses a screw to install, or the Replacement Handle for Bladex and Valterra Waste Valves # T1003-6MNVP which threads onto the waste valve. If you aren't sure what you have just send me some photos and I can try to help you out.
Since these handles use threads to install you shouldn't have any problems... view full answer...
Realistically there would be no reason or advantage to switch from a 205/75-14 tire to a 215/75-14 tire, although the 215/75-14 will fit your current wheel. If you are looking for a radial tire, you could get a radial tire that is the same size you have now like the Karrier ST205/75R14 Radial Trailer Tire - Load Range D # AM10235.
This tire will have the same/similar outer diameter and section width of your current tire. The difference is minimal between the 205/75-14 and 215/75-14, but... view full answer...
While we do not carry the Lippert Road Armor currently for triple axle setups I do have a couple kits for you to consider to replace the MORryde Rubber Equalizers # MR39ZR you have on your 2019 Heartland Cyclone 4270 Toy Hauler.
First is the Lippert Center Point by Trailair Air-Ride Suspension Upgrade # LC1565401. This will replace the rubber equalizers you have with an air cushioned suspension. It will allow you to be able to adjust the air pressure to fine tune your desired ride quality.... view full answer...
Your 2019 Heartland Cyclone model 4270 5th wheel is going to need the 35" Equalizers # MR39ZR like you found. You can verify this if you like by measuring from the center of the center wheel to the center of the front and rear axles. You will also need the MORryde Suspension Upgrade Kit # MR26ZR. view full answer...
We do have the replacement gearbox you need for your Venture VMC940RB, which is the following part:
- Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies # LC276602
I have added a link below to a video review for you to check out as well if you'd like. view full answer...
I'd be happy to provide those for you. The # FR52FR replacement oven door measures 21-7/8 x 11-3/4 x 3-5/8 inches thick (including the handle).
I've shown these dimensions on a photo for you. view full answer...
We do have the Replacement Fan Motor Assembly Kit for Fan-Tastic Vent Roof Vent Fans # FVK8017-00, which will work to replace the bow-tie bracket, motor, and blade for your Create-a-breeze model 8100RDMS.
We do not carry the Create-a-breeze model 8100RDMS itself. But the Fan-Tastic Vent Roof Vent w/ 12V Fan # FV802250 will fit and from what I found, it appears to have the same features as the Create-a-breeze model 8100RDMS. view full answer...
Thank you for the photos and measurement!
We have a variety of slide out wiper seals that might work for your application but you'll want to look underneath/behind the seals you have pictured to make sure they don't have any other kind of design as well since that can change from slide out to slide out.
If you do indeed have a flat wiper seal then what we have that is closest to your seal is the 3" seal from Steele Rubber. Part # SR29FR gets you a 15' strip while part # SR56FR gets you... view full answer...
It sounds like you want an upgraded equalizer to replace your Dexter 12-142 equalizers. I recommend the # LC314336 you were looking at for a replacement. This matches the length of your current equalizer, which is the most important factor when choosing a replacement. The Equa-Flex will help absorb road shock and improve your ride while towing your trailer.
For shackles and wet bolts, I recommend the MORryde Suspension Upgrade Kit for Tandem Axle Trailers. This kit comes with wet bolts,... view full answer...
The Valterra Waste Valve Bodies w/ Flexible Cables for RV Black Water and Gray Water Tanks - 72" Item # TC1372 is a correct replacement for your gray and black tank valves. I have attached a picture from the guide to help with placement of the cable/handle. view full answer...
Go To Results